Skip to main content

Is there enough volatility in the markets this week?

Those of you watching the markets this week are probably asking the same question this week, wondering if consumers here in the province will see a drop in fuel pricing: Is there enough volatility in the markets right now, to warrant a drop in prices?
This week shows a drop of almost seven bucks a barrel US with corresponding spot prices dropping by nearly five cents on a litre after yesterdays market close. While my average for the last pricing session was set at 58.05 cents a litre, that average has touched near three cents after yesterdays market activity. The average for the preceding six days I now have at 55.38 cents a litre, a difference of close to 2.7 cents a litre.
Interruption requires that four cents a litre, up or down, from the previous price setting, are needed for interruption to occur.
That being said, again today, we're looking at gasoline trading down by another two cents a US gallon and that number does not include any market volatility that my numbers do not record.
There is a possibility that gasoline prices may be adjusted downwards after Wednesday night as a result of that, market volatility.
Other fuels like heating oils, stove oils and diesels, are also down but are less than the 2.7 or so that I have for gasoline.
Trouble here is that I also have numbers for the first six days that also shows greater than 3.4 cents a litre down on gasoline, taxes not included.
With oil prices collapsing again in the face of weakening demand and bad economic news, it may be well advised to hold back on any purchases you might want to make in the next day or so, that is, until we see what the Public Utilities Board is going to do this coming Thursday.
Those in other jurisdictions might want to follow the same advice: drops in pricing are on the way!
I'll know more after tonight's numbers come in for Newfoundland and Labrador, so stay tuned!
It's going to be close!

Popular posts from this blog

Vertical Lube Oil Pumps (Model VCRE)

Lube oil pumping applications demand a pump that provides reliability and extended service life with a minimum of maintenance. The typical Lube Oil pump must also be capable of operation over a wide range of temperature and liquid viscosity conditions. The VCRE family of pumps is designed specifically with these requirements in mind. The VCRE lube oil pump is a vertically submerged pump that utilizes an ANSI standard hydraulic construction, enclosed bearing housing, and welded piping construction which eliminates the inherent maintenance and leakage problems associated with other pumps. During operation, axial and radial thrust loads are controlled by Buffalo’s exclusive modified casing volute and impeller design.  is backed by extensive field-proven experience in designing pumps to handle any lube oil application. This experience also provides flexibility in assisting OEM’s contractors and end-users in designing a sound instal...

Motorcycle Shaft Drive Grease

General Purpose Grease Grease has several uses on a motorcycle. It's there to protect parts from water, to keep rubber and plastic seals from drying out, and to provide lubrication. Generally speaking, grease is just a reduced fat. In fact, you can find several companies who call their grease bases "soap." The choice for a general purpose grease to protect from water, keep seals moist, and provide lubrication is easy. If you're going to do your own maintenance, I recommend you get Mobil-1 or Valvoline synthetic grease for general purposes, about $6 / pound anywhere. This stuff can handle temperatures higher and lower than you'll ever get near. A one pound jar should last you about 15 years. Shaft Drive Gear Maintenance There are two types of maintenance you must do on a shaft drive bike. At your rear wheel there are pinion gears where the spinning drive shaft motion is turned 90 degrees into the rear wheel motion. These gears are bathed in oil which much be c...

Understanding Ferrous Density

As part of my job, I regularly present oil analysis training seminars. One of the tests we discuss is ferrous density. I find that this test is seldom well understood, and, probably as a result, is seldom used. Explanation of the Test Ferrous density is the density of ferrous, or more correctly, of ferromagnetic particles distributed in the oil. The other ferromagnetic elements that one might encounter in lubricated components are nickel and cobalt, but in practice, these elements are likely to be present only in comparatively small quantities. Therefore, we are effectively measuring the concentration of magnetic steel alloys. There is no single way to conduct a ferrous density analysis. There are many ways of performing this rather essential test. Perhaps the two most common are the direct-reading ferrography, a technique which uses light blockage analysis of material deposited on a glass slide; and electromagnetic induction, which measures the voltage induced in a current-carrying ...