Skip to main content

Gas and Oil

Gas and Oil

Posted: 17 Nov 2009 07:21 PM PST

Modest drops in pricing on the way

Media release

Conception Bay South, NL, November 17, 2009- There will be some retreat in petroleum pricing this coming Thursday, that's according to George Murphy, group researcher and member of the Consumer Group for Fair Gas Prices.

"There's not a big lot there for the consumer but, at least the numbers are pointing down according to the data I have," said Murphy. "While oil has been trading in a volatile way the past two weeks, it has always returned to the $80 dollar a barrel mark and that volatility shows itself in bullish spot pricing numbers."

"Consumers should see stove oils drop by 1.37 cents per litre, diesel to drop by 2.0 cents a litre and gasoline should drop by 2.3 cents, that's with all fourteen days of data in hand now. Heating oils should drop by close on what I have for stove oils, but with the jet fuel component remaining a missing factor in figuring out its trend, we can only go by the stove oil number to surmise what will happen with pricing there.

"Good economic news is helping to support pricing of oil products this past session. Signs of economic recovery are helping to spur investment in commodities over the US dollar and that helps to support pricing. In spite of this, related commodity pricing of petroleum products fell from last week as a result of builds in crude oil, gasoline and distillate supply.

"That fact, together with a drop in refiner capacity to a near historic low of close on 79 per cent, is still signifying some possible trouble for supported oil prices in the future when more refineries come back on-line after maintenance shutdowns. Look for oil prices to remain close to where they are now for the time being until the economy shows more proof of consumption of available inventory."

-30-

For more information, contact;

George Murphy
Group researcher/Member

Popular posts from this blog

Vertical Lube Oil Pumps (Model VCRE)

Lube oil pumping applications demand a pump that provides reliability and extended service life with a minimum of maintenance. The typical Lube Oil pump must also be capable of operation over a wide range of temperature and liquid viscosity conditions. The VCRE family of pumps is designed specifically with these requirements in mind. The VCRE lube oil pump is a vertically submerged pump that utilizes an ANSI standard hydraulic construction, enclosed bearing housing, and welded piping construction which eliminates the inherent maintenance and leakage problems associated with other pumps. During operation, axial and radial thrust loads are controlled by Buffalo’s exclusive modified casing volute and impeller design.  is backed by extensive field-proven experience in designing pumps to handle any lube oil application. This experience also provides flexibility in assisting OEM’s contractors and end-users in designing a sound instal...
Read more

Motorcycle Shaft Drive Grease

General Purpose Grease Grease has several uses on a motorcycle. It's there to protect parts from water, to keep rubber and plastic seals from drying out, and to provide lubrication. Generally speaking, grease is just a reduced fat. In fact, you can find several companies who call their grease bases "soap." The choice for a general purpose grease to protect from water, keep seals moist, and provide lubrication is easy. If you're going to do your own maintenance, I recommend you get Mobil-1 or Valvoline synthetic grease for general purposes, about $6 / pound anywhere. This stuff can handle temperatures higher and lower than you'll ever get near. A one pound jar should last you about 15 years. Shaft Drive Gear Maintenance There are two types of maintenance you must do on a shaft drive bike. At your rear wheel there are pinion gears where the spinning drive shaft motion is turned 90 degrees into the rear wheel motion. These gears are bathed in oil which much be c...
Read more

Understanding Ferrous Density

As part of my job, I regularly present oil analysis training seminars. One of the tests we discuss is ferrous density. I find that this test is seldom well understood, and, probably as a result, is seldom used. Explanation of the Test Ferrous density is the density of ferrous, or more correctly, of ferromagnetic particles distributed in the oil. The other ferromagnetic elements that one might encounter in lubricated components are nickel and cobalt, but in practice, these elements are likely to be present only in comparatively small quantities. Therefore, we are effectively measuring the concentration of magnetic steel alloys. There is no single way to conduct a ferrous density analysis. There are many ways of performing this rather essential test. Perhaps the two most common are the direct-reading ferrography, a technique which uses light blockage analysis of material deposited on a glass slide; and electromagnetic induction, which measures the voltage induced in a current-carrying ...
Read more